![2200 ohm resistor color code 2200 ohm resistor color code](http://www.thebackshed.com/windmill/Docs/images/resistor-colour-codes.jpg)
![2200 ohm resistor color code 2200 ohm resistor color code](http://vintageradio.me.uk/info/imageinfo/reschart.jpg)
- #2200 ohm resistor color code how to
- #2200 ohm resistor color code manual
- #2200 ohm resistor color code skin
- #2200 ohm resistor color code code
It will not work!Ĭut the yellow wire, and the black wire, leaving as much wire as possible on the ends that do not go to the ignition switch. In that case, do not continue with this project. If they are wrapped with black fabric tape, unwrap them and separate the three wires so you can determine which is yellow, black, and white.ĬAUTION: If a remote start or alarm system has been installed on your vehicle, the wiring has probably been modified. They will be near the end of the switch where the key is inserted. Three thin wires, possibly taped together with fabric tape, will be visible coming from the top of the ignition switch. On the left side of the radio cavity, there will be an opening, through which you will be able to see the Ignition Switch. Disconnect the wiring connector and the antenna wire, and set the radio aside. Use a 5/16 inch socket to remove the three screws holding the radio in place. Once you get it loose, disconnect the cables that go to the two lights at the top of the bezel, and the cigarette lighter socket. You can pry it loose with a large screwdriver, or a sturdy dinner knife. Important: Disconnect one of the terminals from the battery before doing any of the following. Replacing the Passlock Sensor with Our Module You will use this module to bypass your security system without having to solder anything. Now you have created the module in the right side of the above photo. Insert the resistor leads into one side of the terminal block and tighten the terminal screws down on both the leads.
#2200 ohm resistor color code code
(The color code for the resistor is three red bands.) When you've finished the above steps, you will have the two parts shown on the right side of the above photo. Takle one of the 2200 ohm resistors and bend the leads as I'm doing here. Set the rest of the terminal strip aside. HERE IS THE LINK GM Passkey NO start BypassĬut two terminals off the end of the terminal strip. NOTE: IF YOU WANT TO AVOID BUILDING THE DUMMY PASSLOCK SENSOR, YOU CAN BUY ONE ON E-BAY. Sharp knife for cutting and stripping wires.Here are links to the 2.2k-ohm Resistor and the Terminal Block If your local Radio Shack store has gone out of business, you can order the parts from Digi-Key Electronics. Go to Radio Shack and buy a Mini Terminal Block, and a package of 2200 ohm (2.2k-Ohm) resistors. Note: Many of the images on this page can be enlarged by right clicking on the image, and selecting "View Image" Supplies Needed Perform the "Relearn" Procedure so that our Body Control Module recognizes our new circuit.īypassing the Passlock Sensor - Step by Step.Find the three wires that connect the Passlock Sensor to the Body Control Module and substitute our circuit for the Passlock Sensor.Build a cheap, simple circuit to take the place of the Passlock Sensor.The three wires can be accessed by removing the radio from the dashboard, and reaching through a hole in the radio compartment toward the steering wheel. The Yellow wire is circuit #1836, and this is the wire that furnishes an analog signal to the Body Control Module to tell it that a key has been used to turn the lock cylinder to the ON position. They are Black (analog return), White (power), and Yellow (analog data). In GM cars, there is a bundle of three wires which go from the Body Control Module to the Ignition Switch.
#2200 ohm resistor color code how to
There are generally only minor differences in how to get the radio out to get to the wires. The steps necessary are similar on the other models listed above. This web page will guide you through the steps necessary to bypass the "Passlock Sensor" on a 2002 Pontiac Grand Am, and keep the "SECURITY" light off forever.
#2200 ohm resistor color code skin
It will get under your skin really bad the third time, and after that, you will start kicking the dash and swearing. This normally works! Unfortunately, a few weeks later, you will probably have to go through the entire routine again. Then turn the ignition to OFF before attempting to start the engine again." "After attempting to start the engine, if the "SECURITY" light flashes or stays on, wait ten minutes with the key in ON until the light goes off.
#2200 ohm resistor color code manual
Your owner's manual gives you the following advise The problem is usually caused by the "Passlock Sensor", which is part of the Ignition Lock Module. This is a common problem on the following GM Cars After you shut down your vehicle, the next time you start your car the SECURITY light is on solid. You are driving along, and for no apparent reason, the "SECURITY" light comes on solid and stays on. The engine starts, but dies in one or two seconds, and the "SECURITY" light begins flashing. This article describes how to bypass the "Passlock Sensor" on several models of GM cars.